Program That Can Draw Floor Plans and Roof

Describe Roof

Hands create these common roof styles.

Contents

Describe Roof

Select Roof and Roof Fashion

Rotate

Peak

Height

Delete

Move

Hide

Lock

Reflections

Resize Roof Surface area

Overhangs

Adjusting Roof Edges

Reset Edges

Hipped and Connected Roofs

Paint and Materials

Cut Holes

Fit Wall to Gabled Roof

Skylights

Odd Roof Types
Dormers


Depict Roof

Use the following steps to draw a roof:

  1. Create a structure to put the roof on.

  2. Cull Build>Draw Roof.

  3. Cursor changes to a transparent disc to gauge drawing tiptop

  4. Position disc on wall top before drawing.

  5. Click-and-drag from one corner of the wall pinnacle to the other.

  6. In wireframe, drag blue handles to outer wall edges to snap in identify.
    (Edit roofs in wireframe mode or finished mode - whichever works all-time.)

    Notation: Likewise run across Roof tutorial.


Select Roof and Roof Mode

Select a roof past double-clicking it. You may also right-click the roof and choose "Select Object."

In that location are two selection modes when working on standard roofs:

Finished Mode: When y'all select a roof and it is solid this is "Finished mode." To switch to wireframe way double-click the roof over again.

Wireframe Mode: When you get-go draw a roof or when you lot double-click a roof that is in finished mode, it will switch to wireframe mode. Yous tin edit roofs in either manner.


Rotate

In wireframe mode rotate the square handle shown in a round motion. Agree in the shift central to disable snap.


Peak

The tiptop handle is the acme center pink handle betwixt the 2 ruby handles. The acme can be adapted vertically and horizontally:

  1. Vertical Height: Elevate acme up or downwardly.

  2. Horizontal Position: Hold in shift key and drag the top left or right to start the handle for Salt-Box roofs.

Example:


Height of Roof

In wireframe mode accommodate roof superlative with the pink handle betwixt the blue handles.

In finished mode adjust the pink handle between the peak and blue handles on the selected roof side.

Example:


Delete

To delete the entire roof, double-click it to get in to wireframe mode and printing the delete or backspace keys.

You may also delete half of the roof in finished mode for special purposes - although Build>Construct Roof (custom) may be a better solution.


Move

Click-and-drag the finished roof or the semi-transparent part of a wireframe roof to slide it around at current height.


Hide

Right-click a roof and choose Hide from the pop-up carte du jour. In wireframe the whole roof is subconscious. In finished mode but the roof one-half you right-click volition be subconscious.

Hide All Roofs by choosing View>Hide>Roofs or press the R key. Prove Roofs by choosing View>Show All.


Lock

To lock a roof and so you can't accidentally alter it, right-click it and choose "Lock." Unlock it the same mode.


Reflections

Right-click the roof, cull "Properties" and prepare reflectivity as a percentage - where a mirror is 100% and no reflectivity is cipher.

To turn on reflections see Edit> Better Edit Speed> Plough Off Reflections or just press the "G" primal. The green dot next to the "M" on the tool bar indicates reflections are on.

Notation: Reflectivity requires more rendering power because plan3D has to re-render this reflect epitome in the countertop. This requires plan3D to practice double-rendering. If yous accept a slow reckoner or video carte you lot should probably turn off reflections when you're editing. Run into Edit> Meliorate Edit Speed for more information.


Resize Roof Area

The roof surface area is the foundation - the part that sits on top of a structure. Roof area is defined as a rectangle, even if the roof edges are reshaped to hang below it.

You lot cannot change the roof area in finished mode.

In wireframe mode conform the blue handles. They'll snap to roof edges if you lot get close. Hold in the shift primal if you need to disable snap.


Overhangs

Create overhangs In finished mode past dragging blue handles downward. To define a subsection for an overhang, Ctrl-click roof edges to add together and delete handles.


Adjusting Roof Edges

Drag blueish or cerise handles on finished roofs to extend roof edges or sides. Hold in the shift key to disable snap to when dragging.

Ascertain width of overhangs by holding downward the Ctrl key and clicking roof edges in finished roof mode (not wireframe.) Also apply the Ctrl fundamental to delete red handles on the edges of finished roof edges (not wireframe.)

Case:


Reset Roof Edges

If roof edges are not working as you expected and you want to reset them and start over, right-click the roof and choose "Reset Roof Edges."


Hipped and Connected Roofs

Create hipped and connected roofs by dragging the top red handles in or outwards.

Example:


Pigment and Materials

Utilise shingles to roof tops by dragging them in from the Directory. Utilize ceiling materials and pigment to the bottoms of roofs from the Directory also. See Paint and Colors and Materials and Textures for more information.


Cut Holes in Roof

Use Build>Cut Hole to cut holes in your roofs.


Fit Wall to Gabled Roof

Hither how to add a indicate to the top of a wall and fit it to the roof elevation:

  1. Create walls and depict a roof on them (Figure ane).

  2. Hold in the Ctrl key and move the mouse over a wall edge. (Figure two.) A dot will appear at the arrow cursor to indicate you may click to add a betoken to it.


    Figure i.                                                      Figure 2.

  3. Subsequently y'all Ctrl-click the wall top, you lot'll see a red handle at that point (Figure iii.)

  4. Drag the red handle upwardly nether the roof top to snap it into place (Figure 4.)


    Figure 3.                                                      Effigy 4.


Skylights

Skylights may exist dragged onto roofs from the Directory> Building Materials> Windows> Skylights (Velux).

Add Ceiling Shafts: If you have a ceiling under the skylight and you desire to driblet a shaft to it, right-click the skylight and choose "Create Shaft" and type of shaft. Right-click shafts and alter their flare every bit well.

Skylight Pitch: If yous change roof pitch with Velux skylights, plan3D will add a back up to it beneath fifteen degrees automatically.


Odd Roof Types

Virtually whatsoever roof blazon you lot tin't create with Draw Roof may be created with Build>Construct Roof (custom).


Dormers

Dormers may drawn on roofs using Build>Draw Dormers.

wardherefaing.blogspot.com

Source: https://www.plan3d.com/p3dhelp/buildDrawRoof.htm

0 Response to "Program That Can Draw Floor Plans and Roof"

ارسال یک نظر

Iklan Atas Artikel

Iklan Tengah Artikel 1

Iklan Tengah Artikel 2

Iklan Bawah Artikel